基于ARM9的智能γ能谱仪器硬件平台的设计

在分析当前流行的嵌入式硬件平台的基础上，结合三星S3C2410A处理器的高性能、低功耗，设计了智能γ能谱仪器的硬件平台，并着重分析了硬件平台的存储器、LCD、键盘控制器的电路设计，为智能γ能谱仪器硬件平台提供了新的解决方案。     

Progress of Solid Electrolytes and the Electrochemical Sensors

Four types of solid state electrochemical sensors and their general principles are introduced in the paper. The novel type-IV sensors developed in the last few years are emphasized to study hereafter. The ways to design new electrochemical sensors and the directions to develop new solid electrolytes for new electrochemical sensors are also discussed.     

溶胶-凝胶法制备(Sr,Pb)TiO3纳米晶粉及表征

采用溶胶－凝胶法成功地合成了（Sr,Pb)TiO3纳米晶粉，并利用FTIR技术对凝胶的形成过程及350℃，1．5h煅烧获得的粉体材料进行了表征。实验以TG－DSC分析作为拟定煅烧温度的依据，以XRD作为煅烧产物的分析手段，最佳煅烧温度为600℃，所合成的（Sr,Pb)TiO3纳米晶粉的平均晶粒尺寸约为21nm，属钙钛矿型立方顺电相结构。     

激光熔覆用钴基合金粉末的研究

对激光熔覆用WFLC－11钴基合金粉末的激光熔覆工艺和熔覆层性能进行了研究，获得了WFLC－11钴基合金粉末激光熔覆层厚度与最小比能量关系曲线和熔覆层的组织、高温硬度等性能数据，为选择和使用WFLC－11钴基合金粉末提供了依据。     

可编程序控制器在催化联锁系统的应用

随着工厂自动化程度的提高，对可编程控制器系统的可靠性要求越来越高，特别是炼油厂、化工厂、电站、钢铁厂以及环保项目中，停车将会给工厂带来的昂贵的代价。在这种情况下,冗余控制器能显著降低生产停滞的风险。简单介绍了可编程序控制器的冗余系统，并结合具体实例说明了冗余系统在其应用过程中的安全可靠性。     

基于SOC的PAGER控制芯片设计

文章讨论了PAGER控制器芯片（ZQD021）的系统设计，该控制器内部集成了FLASH，SRAM，POCSAG协议解码器和嵌入式MCU CORE。重点分析了芯片的可测性设计（DFT），内嵌FLASH设计，低功耗设计，其设计方法和思路对消费类和嵌入式控制芯片的设计有一定的借鉴意义。     

Matrix expression and reachability analysis of finite automata

In this paper,we propose a matrix-based approach for finite automata and then study the reachability conditions.Both the deterministic and nordeterministic automata are expressed in matrix forms,and th...     

软件项目质量控制流程及其技术

软件项目质量管理是贯穿整个软件生命周期的重要工作,有效地实施质量控制是提高软件质量、降低成本的重要手段。针对质量控制的难点,对质量控制流程与技术进行研究。首先,说明质量控制过程,包括事前质量控制、事中质量控制和事后质量控制;然后,通过图形研究质量控制流程;最后,通过图形并结合文字说明研究质量控制技术,包括因果图、Pareto图、控制图、运行图、统计抽样等5种常用技术。结果表明,通过对质量控制流程与技术的研究,为质量控制提供技术和方法支持,提高质量管理的科学性。     

Multi-channel SAR imaging based on distributed compressive sensing

The rapid development of compressive sensing(CS)shows that it is possible to recover a sparse signal from very limited measurements.Synthetic aperture radar(SAR)imaging based on CS can reconstruct the target scene with a reduced number of collected samples by solving an optimization problem.For multi-channel SAR imaging based on CS,each channel requires sufficient samples for separate imaging and the total number of samples could still be large.We propose an imaging algorithm based on distributed compressive sensing(DCS)that reconstructs scenes jointly under multiple channels.Multi-channel SAR imaging based on DCS not only exploits the sparsity of the target scene,but also exploits the correlation among channels.It requires significantly fewer samples than multi-channel SAR imaging based on CS.If multiple channels offer different sampling rates,DCS joint processing can reconstruct target scenes with a much more flexible allocation of the number of measurements offered by each channel than that used in separate CS processing.